X2Go - everywhere@home

User Tools

Site Tools

Trace:
doc:howto:tce

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision Both sides next revision
doc:howto:tce [2018/02/12 14:48]
stefanbaur [List of open ToDos/FIXMEs for this page] explained how parameters currently unsupported in MiniDesktop mode could be made to work 		doc:howto:tce [2018/02/12 14:54]
stefanbaur [What options are available under FURTHER-OPTIONS-GO-HERE?] - added homepageurl description
Line 884: Line 884:
   * ''copysecring'' - this will scan for USB media and fixed disk media (with USB media taking precedence) at boot for one or more of the following directories: ''config/ssh'', 'ssh', ''.ssh''. The volume must be labeled ''X2GO-TCE-LIVE'' or ''PORTABLEAPP'' and may use any supported file system. Any SSH Secret Keys found there will be copied into ''/home/user/.ssh'' (in the ramdisk), with proper permissions and ownerships for the default user account. This may come in handy when you are using SSH Secret Keys on USB media, but need to log in and out of sessions often, and don't want to leave the USB media plugged in all the time/don't want to have to re-insert it before each session startup. **Attention: This poses a security risk when other people are using your ThinClient afterwards (as they will have access to your keys).**  To mitigate this risk,be sure to power-cycle the ThinClient once you are done. You //should// specify this parameter when booting X2Go-TCE-Live from portable media when you want to use SSH Secret Keys, to make sure your secret key on the VAT/NTFS partition is available. But as stated above, be sure to power-cycle the machine once you're done.   * ''copysecring'' - this will scan for USB media and fixed disk media (with USB media taking precedence) at boot for one or more of the following directories: ''config/ssh'', 'ssh', ''.ssh''. The volume must be labeled ''X2GO-TCE-LIVE'' or ''PORTABLEAPP'' and may use any supported file system. Any SSH Secret Keys found there will be copied into ''/home/user/.ssh'' (in the ramdisk), with proper permissions and ownerships for the default user account. This may come in handy when you are using SSH Secret Keys on USB media, but need to log in and out of sessions often, and don't want to leave the USB media plugged in all the time/don't want to have to re-insert it before each session startup. **Attention: This poses a security risk when other people are using your ThinClient afterwards (as they will have access to your keys).**  To mitigate this risk,be sure to power-cycle the ThinClient once you are done. You //should// specify this parameter when booting X2Go-TCE-Live from portable media when you want to use SSH Secret Keys, to make sure your secret key on the VAT/NTFS partition is available. But as stated above, be sure to power-cycle the machine once you're done.
   * ''earlyblankdpmsfix'' - This forces the TFT do black for a few seconds during the initial boot phase (right after the squashfs was downloaded), then forces it back on again.  This fixes an occasional "black screen" issue that occurs with some flaky client/TFT hardware combinations when using DisplayPort connectors, and could otherwise only be remediated by manually turning the TFT off and back on again. (feature available via github repo, soon via x2go repo too)   * ''earlyblankdpmsfix'' - This forces the TFT do black for a few seconds during the initial boot phase (right after the squashfs was downloaded), then forces it back on again.  This fixes an occasional "black screen" issue that occurs with some flaky client/TFT hardware combinations when using DisplayPort connectors, and could otherwise only be remediated by manually turning the TFT off and back on again. (feature available via github repo, soon via x2go repo too)
 +  * ''homepageurl="URL1[|URL2|URLn]"'' - this is only available in MiniDesktop mode. It allows you to specify one or more web pages that show up on Browser start/when clicking the "Home" icon. URLs need to be separated with a ''|'', and the set of URLs needs to be enclosed in double quotes. Do //not// enclose each URL in double quotes separately! Correct example: ''homepageurl="https://www.google.de|https://wiki.x2go.org"''
   * ''ldap=ldap.example.com:389:cn=cngoeshere,dc=example,dc=com'' - this allows you to specify an LDAP server to connect to - note that this is not needed for LDAP-based authentication, only when you intend to store entire session profiles in LDAP. You should really consider using the X2Go Session Broker instead.   * ''ldap=ldap.example.com:389:cn=cngoeshere,dc=example,dc=com'' - this allows you to specify an LDAP server to connect to - note that this is not needed for LDAP-based authentication, only when you intend to store entire session profiles in LDAP. You should really consider using the X2Go Session Broker instead.
   * ''ldap1=ldap-backupserver-1.example.com:389'' - this allows you to specify the first of up to two LDAP backup servers when using LDAP authentication   * ''ldap1=ldap-backupserver-1.example.com:389'' - this allows you to specify the first of up to two LDAP backup servers when using LDAP authentication
doc/howto/tce.txt ยท Last modified: 2024/01/26 19:49 by stefanbaur

Page Tools

Imprint & Legal Disclaimer - Data Protection & Privacy Statement
Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
GNU Free Documentation License 1.3 Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki