This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
doc:installation:x2goserver [2015/01/04 17:50] mikedep333 [Installing Required Dependencies (fuse and perl modules)] Specify perl(DBI::db) (The version in EL5 is too old) |
doc:installation:x2goserver [2016/11/02 05:28] ionic Remove the OBS section for EPEL 5, it's probably not a good idea to keep that in the current state. |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== X2Go Server installation ====== | ====== X2Go Server installation ====== | ||
- | Please see [[wiki: | + | Please see [[wiki: |
Line 60: | Line 60: | ||
</ | </ | ||
+ | Then, install '' | ||
===== Fedora 19 and later ===== | ===== Fedora 19 and later ===== | ||
Line 76: | Line 77: | ||
Check that you have activated the " | Check that you have activated the " | ||
<code bash> | <code bash> | ||
- | sudo rhn-channel | + | sudo subscription-manager repos --list |
</ | </ | ||
If the optional channel for your base channel is not active, activate it. | If the optional channel for your base channel is not active, activate it. | ||
<code bash> | <code bash> | ||
- | sudo rhn-channel | + | sudo subscription-manager repos --enable=rhel-7-server-optional-rpms |
</ | </ | ||
Or use the RHNS web interface to activate the channel "RHEL Server Optional" | Or use the RHNS web interface to activate the channel "RHEL Server Optional" | ||
Line 92: | Line 93: | ||
===== RHEL 6 ===== | ===== RHEL 6 ===== | ||
- | There are two sources for X2Go packages for RHEL 6 - Fedora EPEL and OBS. Follow one of the following two links to configure the repository of your choice. | + | There are two sources for X2Go packages for RHEL 6 - our packages repository and Fedora EPEL. |
- | + | ||
- | ==== EPEL ==== | + | |
- | + | ||
- | [[https:// | + | |
- | + | ||
- | ==== OBS ==== | + | |
- | [[wiki: | + | |
+ | Select **one method only** and follow [[wiki: | ||
==== Activating Optional Channels for RHEL ==== | ==== Activating Optional Channels for RHEL ==== | ||
Line 145: | Line 140: | ||
sudo yum install x2goserver-xsession | sudo yum install x2goserver-xsession | ||
</ | </ | ||
- | ===== RHEL 5 ===== | ||
- | <note warning> | + | ===== EPEL 5 (via packages.x2go.org) ===== |
- | [[wiki: | + | <note warning> |
+ | |||
+ | [[wiki: | ||
==== Installing Required Dependencies (fuse and perl modules) ==== | ==== Installing Required Dependencies (fuse and perl modules) ==== | ||
=== Download required packages manually === | === Download required packages manually === | ||
Line 155: | Line 151: | ||
One approach is to download required packages manually. Yum will tell you what is needed, when you ask it to install '' | One approach is to download required packages manually. Yum will tell you what is needed, when you ask it to install '' | ||
+ | * perl(DBI:: | ||
* perl(File:: | * perl(File:: | ||
- | * perl(Sys:: | + | * perl(Sys:: |
* fuse - fuse-2.7.4-8.el5.x86_64.rpm | * fuse - fuse-2.7.4-8.el5.x86_64.rpm | ||
* libfuse.so.2 - fuse-libs-2.7.4-8.el5.x86_64.rpm | * libfuse.so.2 - fuse-libs-2.7.4-8.el5.x86_64.rpm | ||
* fuse-sshfs - fuse-sshfs-2.2-1.el5.rf.x86_64.rpm | * fuse-sshfs - fuse-sshfs-2.2-1.el5.rf.x86_64.rpm | ||
- | * perl(DBI:: | ||
- | * '' | + | * '' |
- | * '' | + | * '' |
==== Installing X2Go Server ==== | ==== Installing X2Go Server ==== | ||
- | You should now be able to install the '' | + | You should now be able to install the '' |
yum install x2goserver | yum install x2goserver | ||
+ | | ||
+ | ===== SUSE ====== | ||
- | Unfortunately, | + | Follow the the instructions for [[wiki:repositories: |
- | Running Transaction | + | ==== Installing |
- | | + | |
- | | + | <code bash> |
- | | + | zypper install x2goserver |
- | | + | </code> |
- | | + | |
- | | + | ==== Workaround for Qt-based Applications and sudo/kdesu ==== |
- | | + | |
- | Installing: makepasswd | + | Please keep this section in sync with the README.sudoers |
- | Installing: libXcompshad3 | + | |
- | Installing: libNX_Xpm4 | + | === Problem Description === |
- | Installing: libNX_Xinerama1 | + | |
- | Installing: libXcompext3 | + | OpenSUSE 11 and SLES/SLED 11 do not support |
- | Installing: libNX_freetype6 | + | custom sudoers config files. |
- | Installing: libNX_Xfixes3 | + | |
- | Installing: libNX_Xdmcp6 | + | If you are using any of these distributions and |
- | Installing: libNX_Xcomposite1 | + | are having issues regarding running Qt applications with elevated privileges |
- | Installing: perl-DBI ####################### | + | (e.g., via kdesu or sudo), please use this workaround. |
- | | + | |
- | | + | |
- | Installing: perl-Config-Simple | + | === Necessary Actions === |
- | Installing: nxagent | + | |
- | Installing: x2goserver | + | |
- | " | + | |
- | Can't continue after import errors at / | + | |
- | BEGIN failed--compilation aborted at / | + | |
- | chgrp: cannot access `/ | + | |
- | | + | |
- | | + | |
- | | + | |
- | " | + | |
- | Can't continue after import errors at /usr/sbin/ | + | |
- | BEGIN failed--compilation aborted at / | + | |
- | | + | |
- | | + | |
- | + | ||
- | | + | |
- | | + | |
- | | + | |
- | Despite being installed | + | - Copy the contents of the "x2goserver" file residing in the documentation directory ''/ |
+ | - Get elevated privileges. Either via <code bash> | ||
+ | - Launch <code bash> | ||
+ | - Paste the previously copied content at the end of the sudoers file. | ||
+ | - Save and exit your editor. | ||
- | Verbindung fehlgeschlagen DBD:: | + | ===== Arch Linux ===== |
+ | '' | ||
+ | See https:// |