This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
doc:installation:x2goserver [2013/03/15 16:38] sunweaver [X2Go Server installation] |
doc:installation:x2goserver [2013/08/29 09:21] zaister Add instruction for Gentoo |
||
---|---|---|---|
Line 35: | Line 35: | ||
sudo apt-get install x2goserver x2goserver-xsession | sudo apt-get install x2goserver x2goserver-xsession | ||
</ | </ | ||
+ | |||
+ | ===== Gentoo ===== | ||
+ | |||
+ | Currently X2Go cannot connect to an openssh server compiled with the HPN patch. To make sure x2goserver works on your Gentoo server, you must recompile net-misc/ | ||
+ | |||
+ | < | ||
+ | net-misc/ | ||
+ | </ | ||
+ | |||
+ | Then recompile net-misc/ | ||
+ | |||
+ | < | ||
+ | emerge -1 net-misc/ | ||
+ | dispatch-conf | ||
+ | / | ||
+ | </ | ||
+ | |||
===== RHEL 6 ===== | ===== RHEL 6 ===== | ||
Line 79: | Line 96: | ||
</ | </ | ||
- | **Warning: | ||
+ | ===== RHEL 5 ===== | ||
+ | |||
+ | [[wiki: | ||
+ | |||
+ | ==== Installing Required Dependencies (fuse and perl modules) ==== | ||
+ | === Download required packages manually === | ||
+ | |||
+ | One approach is to download required packages manually. Yum will tell you what is needed, when you ask it to install '' | ||
+ | |||
+ | * perl(File:: | ||
+ | * perl(Sys:: | ||
+ | * fuse - fuse-2.7.4-8.el5.x86_64.rpm | ||
+ | * libfuse.so.2 - fuse-libs-2.7.4-8.el5.x86_64.rpm | ||
+ | * fuse-sshfs - fuse-sshfs-2.2-1.el5.rf.x86_64.rpm | ||
+ | |||
+ | * '' | ||
+ | * '' | ||
+ | |||
+ | ==== Installing X2Go Server ==== | ||
+ | You should now be able to install the '' | ||
+ | |||
+ | yum install x2goserver | ||
+ | |||
+ | Unfortunately, | ||
+ | |||
+ | Running Transaction | ||
+ | Installing: libXcomp3 | ||
+ | Installing: libNX_X11-6 | ||
+ | Installing: libNX_Xext6 | ||
+ | Installing: libNX_Xrender1 | ||
+ | Installing: libNX_Xrandr2 | ||
+ | Installing: libNX_Xtst6 | ||
+ | Installing: libNX_Xdamage1 | ||
+ | Installing: makepasswd | ||
+ | Installing: libXcompshad3 | ||
+ | Installing: libNX_Xpm4 | ||
+ | Installing: libNX_Xinerama1 | ||
+ | Installing: libXcompext3 | ||
+ | Installing: libNX_freetype6 | ||
+ | Installing: libNX_Xfixes3 | ||
+ | Installing: libNX_Xdmcp6 | ||
+ | Installing: libNX_Xcomposite1 | ||
+ | Installing: perl-DBI | ||
+ | Installing: perl-DBD-Pg | ||
+ | Installing: perl-DBD-SQLite | ||
+ | Installing: perl-Config-Simple | ||
+ | Installing: nxagent | ||
+ | Installing: x2goserver | ||
+ | " | ||
+ | Can't continue after import errors at / | ||
+ | BEGIN failed--compilation aborted at / | ||
+ | chgrp: cannot access `/ | ||
+ | chmod: cannot access `/ | ||
+ | Installing: x2goagent | ||
+ | Installing: x2goserver | ||
+ | " | ||
+ | Can't continue after import errors at / | ||
+ | BEGIN failed--compilation aborted at / | ||
+ | chgrp: cannot access `/ | ||
+ | chmod: cannot access `/ | ||
+ | | ||
+ | Installed: x2goserver.i386 0: | ||
+ | Dependency Installed: libNX_X11-6.x86_64 0: | ||
+ | Complete! | ||
+ | |||
+ | Despite being installed x2goserver is dysfunctional afterwards. On connection it yields an error: | ||
+ | |||
+ | Verbindung fehlgeschlagen DBD:: | ||