This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
wiki:repositories:raspbian [2016/11/25 10:45] ionic Grammar, markup. |
wiki:repositories:raspbian [2019/09/12 17:13] ionic Switch main example from stretch to buster. |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== X2Go Packages for Raspbian GNU/Linux ====== | ====== X2Go Packages for Raspbian GNU/Linux ====== | ||
- | To get started you'll need to configure your local system to access the official X2Go Raspbian repository. Please keep in mind that this installation manual will guide you through the installation on a Raspbian jessie system. Only the armhf architecture is supported. | + | To get started you'll need to configure your local system to access the official X2Go Raspbian repository. Please keep in mind that this installation manual will guide you through the installation on a Raspbian jessie, stretch or buster |
===== Adding This Repository To Your Package System ===== | ===== Adding This Repository To Your Package System ===== | ||
- | ==== Adding | + | ==== Bootstrapping |
- | Before starting | + | <note important> |
+ | |||
+ | Please switch to a user which has administrator privileges on your system in your preferred command line client: | ||
<code bash> | <code bash> | ||
Line 19: | Line 21: | ||
- | <note warning> | + | The following |
- | + | ||
- | The following | + | |
<code bash> | <code bash> | ||
$ apt-key adv --recv-keys --keyserver keys.gnupg.net E1F958385BFE2B6E | $ apt-key adv --recv-keys --keyserver keys.gnupg.net E1F958385BFE2B6E | ||
Line 31: | Line 30: | ||
Please add the file '' | Please add the file '' | ||
This can be done by using your preferred editor. | This can be done by using your preferred editor. | ||
+ | |||
+ | < | ||
<code bash> | <code bash> | ||
Line 36: | Line 37: | ||
</ | </ | ||
- | Then add the X2Go repository (binaries and sources) as a couple of new lines (example for Raspbian **jessie**): | + | Then add the X2Go repository (binaries and sources) as a couple of new lines (example for Raspbian **buster**): |
<file - x2go.list> | <file - x2go.list> | ||
# X2Go Repository (release builds) | # X2Go Repository (release builds) | ||
- | deb http:// | + | deb http:// |
# X2Go Repository (sources of release builds) | # X2Go Repository (sources of release builds) | ||
- | deb-src http:// | + | deb-src http:// |
+ | |||
+ | # X2Go Repository (Saimaa ESR builds) | ||
+ | #deb http:// | ||
+ | # X2Go Repository (sources of release builds) | ||
+ | #deb-src http:// | ||
# X2Go Repository (nightly builds) | # X2Go Repository (nightly builds) | ||
- | #deb http:// | + | #deb http:// |
# X2Go Repository (sources of nightly builds) | # X2Go Repository (sources of nightly builds) | ||
- | #deb-src http:// | + | #deb-src http:// |
</ | </ | ||
+ | **Edit this new data** and make sure to uncomment desired components and comment non-desired components. Only one group may be active at a given time. | ||
- | **Note:** If you have not got a folder | + | <note warning> |
+ | |||
+ | <note warning> | ||
==== Synchronize the Newly Added Repository' | ==== Synchronize the Newly Added Repository' | ||
Line 60: | Line 69: | ||
$ apt-get update | $ apt-get update | ||
</ | </ | ||
+ | |||
+ | <note important> | ||
+ | \\ \\ | ||
+ | **Not being able to verify signatures means that any content downloaded from the remote location could be injected/ | ||
+ | \\ \\ | ||
+ | You can bypass apt's internal checks **if you understand the implications** and are ready to take the risk by **once** using: | ||
+ | \\ \\ | ||
+ | <code bash> | ||
+ | $ apt-get update --allow-insecure-repositories | ||
+ | </ | ||
+ | |||
+ | Otherwise, please try to first fetch the key again as outlined in the bootstrapping instructions. | ||
+ | </ | ||
After the update you should be able to access the X2Go packages via the apt command family. As a first action you should install our '' | After the update you should be able to access the X2Go packages via the apt command family. As a first action you should install our '' |