This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
wiki:repositories:debian [2016/09/22 07:41] ionic Fix wikilinks. |
wiki:repositories:debian [2021/07/28 19:21] gratuxri [Adding the Actual Repository] |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== X2Go Packages for Debian GNU/Linux ====== | ====== X2Go Packages for Debian GNU/Linux ====== | ||
- | To get started you'll need to configure your local system to access the official X2Go Debian repository. Please keep in mind that this installation manual will guide you through the installation on a Debian wheezy (jessie, stretch, sid) system. | + | To get started you'll need to configure your local system to access the official X2Go Debian repository. Please keep in mind that this installation manual will guide you through the installation on a Debian wheezy (jessie, stretch, buster, bullseye, sid) system. |
__Exceptions: | __Exceptions: | ||
- | * **Deprecated Debian releases**: please refer to [[wiki: | + | * **Deprecated Debian releases**: please refer to [[wiki: |
- | * **Debian squeeze: **X2Go packages will be offered for Debian squeeze at least until squeeze is still officially supported as '' | + | |
- | * **ARM architecture: | + | |
- | ===== Adding | + | ===== Adding |
- | ==== Adding | + | ==== Bootstrapping |
- | Before starting | + | <note important> |
+ | |||
+ | Please switch to a user which has administrator privileges on your system in your preferred command line client: | ||
<code bash> | <code bash> | ||
Line 24: | Line 24: | ||
- | The following | + | The following |
<code bash> | <code bash> | ||
- | $ apt-key adv --recv-keys --keyserver | + | $ apt-key adv --recv-keys --keyserver |
</ | </ | ||
Line 34: | Line 33: | ||
Please add the file '' | Please add the file '' | ||
This can be done by using your preferred editor. | This can be done by using your preferred editor. | ||
+ | |||
+ | < | ||
<code bash> | <code bash> | ||
Line 39: | Line 40: | ||
</ | </ | ||
- | Then add the X2Go repository (binaries and sources) as a couple of new lines (example for Debian **jessie**): | + | Then add the X2Go repository (binaries and sources) as a couple of new lines (example for Debian **buster**): |
<file - x2go.list> | <file - x2go.list> | ||
# X2Go Repository (release builds) | # X2Go Repository (release builds) | ||
- | deb http:// | + | deb http:// |
# X2Go Repository (sources of release builds) | # X2Go Repository (sources of release builds) | ||
- | deb-src http:// | + | deb-src http:// |
+ | |||
+ | # X2Go Repository (Saimaa ESR builds) | ||
+ | #deb http:// | ||
+ | # X2Go Repository (sources of Saimaa ESR builds) | ||
+ | #deb-src http:// | ||
# X2Go Repository (nightly builds) | # X2Go Repository (nightly builds) | ||
- | #deb http:// | + | #deb http:// |
# X2Go Repository (sources of nightly builds) | # X2Go Repository (sources of nightly builds) | ||
- | #deb-src http:// | + | #deb-src http:// |
</ | </ | ||
+ | **Edit this new data** and make sure to uncomment desired components and comment non-desired components. Only one group may be active at a given time. | ||
- | **Note:** If you have not got a folder | + | <note warning> |
+ | <note warning> | ||
+ | |||
+ | ==== Adding the x2go Repository with extrepo on debian ==== | ||
+ | <code bash> | ||
+ | $ sudo apt install extrepo | ||
+ | $ sudo extrepo enable x2go | ||
+ | </ | ||
==== Synchronize the Newly Added Repository' | ==== Synchronize the Newly Added Repository' | ||
Line 63: | Line 77: | ||
$ apt-get update | $ apt-get update | ||
</ | </ | ||
+ | |||
+ | <note important> | ||
+ | \\ \\ | ||
+ | **Not being able to verify signatures means that any content downloaded from the remote location could be injected/ | ||
+ | \\ \\ | ||
+ | You can bypass apt's internal checks **if you understand the implications** and are ready to take the risk by **once** using: | ||
+ | \\ \\ | ||
+ | <code bash> | ||
+ | $ apt-get update --allow-insecure-repositories | ||
+ | </ | ||
+ | |||
+ | Otherwise, please try to first fetch the key again as outlined in the bootstrapping instructions. | ||
+ | </ | ||
After the update you should be able to access the X2Go packages via the apt command family. As a first action you should install our '' | After the update you should be able to access the X2Go packages via the apt command family. As a first action you should install our '' | ||
Line 81: | Line 108: | ||
- | ===== Mirroring | + | ===== Mirroring |
The packages in this repository can be mirrored via '' | The packages in this repository can be mirrored via '' |