This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
doc:installation:x2goserver [2013/08/23 12:41] holger.krause [RHEL 5] |
doc:installation:x2goserver [2014/09/22 15:47] bengt.giger Update installation for RHEL6, Fedora |
||
---|---|---|---|
Line 7: | Line 7: | ||
==== Quick ==== | ==== Quick ==== | ||
- | You might have to install '' | + | You might have to install '' |
+ | |||
+ | To install '' | ||
<code bash> | <code bash> | ||
sudo apt-get install python-software-properties | sudo apt-get install python-software-properties | ||
</ | </ | ||
+ | To install '' | ||
+ | <code bash> | ||
+ | sudo apt-get install python-software-common | ||
+ | </ | ||
+ | |||
+ | Once '' | ||
<code bash> | <code bash> | ||
sudo add-apt-repository ppa: | sudo add-apt-repository ppa: | ||
sudo apt-get update | sudo apt-get update | ||
- | sudo apt-get install x2goserver | + | sudo apt-get install x2goserver |
</ | </ | ||
Line 34: | Line 42: | ||
<code bash> | <code bash> | ||
sudo apt-get install x2goserver x2goserver-xsession | sudo apt-get install x2goserver x2goserver-xsession | ||
+ | </ | ||
+ | |||
+ | ===== Gentoo ===== | ||
+ | |||
+ | Currently X2Go cannot connect to an openssh server compiled with the HPN patch. To make sure x2goserver works on your Gentoo server, you must recompile net-misc/ | ||
+ | |||
+ | < | ||
+ | net-misc/ | ||
+ | </ | ||
+ | |||
+ | Then recompile net-misc/ | ||
+ | |||
+ | < | ||
+ | emerge -1 net-misc/ | ||
+ | dispatch-conf | ||
+ | / | ||
+ | </ | ||
+ | |||
+ | ===== Fedora 19 and later ===== | ||
+ | |||
+ | No additional repositories required: | ||
+ | |||
+ | <code bash> | ||
+ | sudo yum install x2goserver | ||
+ | </ | ||
+ | |||
+ | ===== RHEL 7 ===== | ||
+ | |||
+ | Add the EPEL repository: | ||
+ | |||
+ | [[https:// | ||
+ | |||
+ | Check that you have activated the " | ||
+ | <code bash> | ||
+ | sudo rhn-channel -l | ||
+ | </ | ||
+ | |||
+ | If the optional channel for your base channel is not active, activate it. | ||
+ | <code bash> | ||
+ | sudo rhn-channel --add -c rhel-x86_64-server-optional-7 | ||
+ | </ | ||
+ | Or use the RHNS web interface to activate the channel "RHEL Server Optional" | ||
+ | |||
+ | Then | ||
+ | <code bash> | ||
+ | sudo yum install x2goserver | ||
</ | </ | ||
===== RHEL 6 ===== | ===== RHEL 6 ===== | ||
+ | There are two sources for X2Go packages for RHEL 6 - Fedora EPEL and OBS. Follow one of the following two links to configure the repository of your choice. | ||
+ | |||
+ | ==== EPEL ==== | ||
+ | |||
+ | [[https:// | ||
+ | |||
+ | ==== OBS ==== | ||
[[wiki: | [[wiki: | ||
Line 79: | Line 140: | ||
</ | </ | ||
+ | if you are installing from EPEL6 or EPEL7, install the '' | ||
+ | <code bash> | ||
+ | sudo yum install x2goserver-xsession | ||
+ | </ | ||
===== RHEL 5 ===== | ===== RHEL 5 ===== | ||